How to Install a Bath Tub Yourself
How to Install a Bath Tub Yourself
Blog Article
Everybody has got their unique assumption about Installing A Bathtub.
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently available, the job can relocate easily; if you need to open a wall to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the job as well as are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed job, it is far better to consider using one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This article will aid you set up a new bath tub in your bathroom if you have currently bought a brand-new bathtub and do not require to alter the setup of your previous water system pipes.
Your tools as well as material checklist need to consist of the following:
Planning for the Installment
To start with, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to stop stress on the bathtub.
Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its final setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of removing the existing faucets can be fairly troublesome due to the restricted accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will originate from the pipelines. When the supply pipes have actually been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before going on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub till the spirit level reads level.
To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water and also check all joints and also new pipework for leaks as well as tighten them if needed. Load the bath tub as well as additionally check the overflow outlet and the normal outlet for leaks.
Lastly, take care of the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the tub has actually been utilized a minimum of when as this will certainly resolve it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type should be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, bring about complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I stumbled upon that article about Installing A Bathtub when exploring the internet. Enjoyed our blog entry? Please share it. Let others locate it. Thanks for your time spent reading it.
Get A Quote
Report this page